PPN- The Leading Source of Industry News on Polymer Pipes and Plastic Pipe Testing
Global News on Plastic Piping and Fittings in Real-Time
NEWSMAKERS: * Aliaxis * Australian Plastic Piping Failures * Baerlocher * BGC * Chris Dearmitt * ExcelPlas * Failure Analysis * FBU * Fletcher Building * Georg Fischer Piping * Iplex * PEX Pipes * PFAS * Plastic Pipe Failures * Polybutylene Pipe Failures * Pro-Fit™ * Ross Taylor * SAPPMA * Uponor * Vinidex
BREAKING NEWS
Georg Fischer Announces it has Gained a 92% Stake in Uponor
Fletcher CEO Sees Litigation Looming on Leaky Aussie Plastic Pipes
Fletcher Building CEO Dodges Key Question as to Why Iplex Changed Resins
When Asked why Iplex Changed PB resins Fletcher CEO Ross Taylor responded “Who knows? I wasn’t here”. 🚩
INDUSTRY ALERT
Lead (Pb) Deposition onto New and Biofilm-laden PEX-A potable Water Pipes
The results revealed greater biofilm biomass on the PEX-A pipes compared to the copper and HDPE pipes. More negative https://www.sciencedirect.com/topics/earth-and-planetary-sciences/zeta-potential was found for the biofilm-laden plastic pipes compared to the new plastic pipes. After five days of Pb exposure under stagnant conditions, the biofilm-laden PEX-A (980 μg m−2) and HDPE (1170 μg m−2) pipes accumulated more than three times the Pb surface loading compared to the new PEX-A (265 μg m−2) and HDPE pipes (329 μg m−2), respectively.
https://www.sciencedirect.com/science/article/abs/pii/S0045653523024050
New Report Published Questioning the Safety of Copper Pipes for Potable Water
INDUSTRY NEWS
Who Owns Georg Fischer Piping?
While institutions own 49% of Georg Fischer AG (VTX:GF), retail investors are its largest shareholders with 51% ownership
Vinidex Hiring HDPE Pipe Extrusion Operators
SAPPMA Webinar Underscores the Importance of Standards for HDPE Pipe Sustainability
The Building Centre in London is holding a free Workshop with Panel Debates and talks led by Experts across the Plastic Pipe industry on 15 November 2023
These expert speakers will be covering a wide array of topics, including Laing O’Rourke’s Jim Jaffa and Christos Pavlou highlighting the latest design trends in piping installations that are striving to make products more efficient. Franz Huelle from REHAU will be discussing the latest innovations in pipework solutions in the industry, whilst Andreas Frank from Borealis will present about renewable feedstock for polymers, which sees vegetable oils being used as a bio-based polymers feedstock. Alongside this, Julia Torrubia and Margarita Kobrina from Atelier Ten will be talking about the impact of plumbing on the whole life cycle of carbon, an important part of the wider picture of sustainability.
Plastic Pipes Prove to Be an Effective Shark Repellent
CONDITION ASSESSMENT
ExcelPlas Pipe Condition Assessment (PCA)
Owners and operators of plants have been using thermoplastics for many years, transporting water, gas and chemicals along their process. However, for operational and maintenance purposes, the asset integrity of the piping system is required. This could be for a number of reason, such as piping system maintenance, ability to maintain current service conditions. EP offers its 30 plus years of plastic piping application experience to assess the fitness for service of used piping. Our specialists inspect the samples in our state-of-the-art accredited materials testing laboratory for piping components, to give our clients the necessary information to make an informed decision and next steps during a project’s operational, maintenance or design phases resolve threats to client assets. ExcelPlas offers the following testing to determine the condition of plastic pipes:
Technical Data:
- Visual Inspection
- Dimensional check
- Oxidation Induction Time (OIT)
- Melt Flow Rate (MFR)
- Fourier-transform Infrared Spectroscopy (FTIR)
- Hydrostatic Test
- Differential Scanning Calorimetry test (DSC)
- Vicat test
- Microscopic analysis
- Report with assessment of the integrity of the piping material
PLASTIC PIPE CONSULTANTS
Plastic Pipe Consulting Experts and Services
If you need a team of pipe plastic experts, then ExcelPlas Consulting is the obvious choice – our size is our strength in a market dominated by single consultants.
We provide services on everything from material selection, product testing, processing to failure analysis
https://www.excelplas.com/contact-us/
PIPE FAILURE ANALYSIS
ExcelPlas Investigating Poly Pipe Failures
Through failure analysis & forensic chemistry, we help clients improve product performance, increase profits, & resolve product liability claims with plastic pipes and fittings.
We are dedicated to unmatched excellence in failure analysis, investigative chemistry, material testing, and expert witnessing for plastics, polymers and composites.
With over 25 years of investigative experience, the staff at ExcelPlas are uniquely positioned to help clients resolve the most challenging performance and processing issues related to materials and finished pipes and fittings.
https://www.excelplas.com/contact-us/
MORE POLY PIPE NEWS
PPN the Digital News Platform for Communicating to the Global Plastic Pipe Industry
Send Us Your News!!! PPN Publishes weekly.
https://www.youtube.com/watch?v=eUKxWbOZY10
ExcelPlas Labs Pipe Failure Investigations
ExcelPlas Labs have created a new benchmark in failure analysis of HDPE, PP-R, PB and PEX pipes in addition to PVC & CPVC pipes as well as composite GRP and GRE pipes. When a plastic pipeline fails to perform as intended, our team can determine the root cause of failure (e.g. oxidative failure, chemical failure, creep failure, over-stress failure, fatigue failure, design failure, etc). ExcelPlas are experienced with all plastic piping failure modes and mechanisms including Slow Crack Growth (SCG) Rapid Crack Propagation (RCP), Environmental Stress Crack Resistance (ESCR), Oxidative Stress Cracking (OSC), cyclic fatigue, manufacturing defects, and polymer material problems.
http://www.excelplas.com/
ExcelPlas Strain Hardening Test (SHT) for HDPE Pipes
The SHT in accordance with ISO 18488 is a relatively new, but excellent way to obtain a rapid indication of the Stress Crack Growth (SCG) resistance of your piping material. This tensile test performed at 80°C has become in just a few years the new standard for Batch Release Testing (BRT). And not without reason. The test requires only a very small amount of material, the results are very reliable with a very low inter-laboratory scatter and the results are available within a few days, regardless of the PE grade. The SHT is usually performed on resin material but it can also be performed on samples taken directly from pipes or sheets. As accredited lab, EXCELPLAS is happy to discuss the possibilities with you, whether it is for BRT, benchmarking, quality control of your (high performing) PE grade or for polymer compliance/ validation.
http://www.excelplas.com/
Australia’s Plastic Pipe Testing Laboratory
ExcelPlas Laboratories provides a comprehensive plastic pipe joint testing service and is equipped with a state-of-the-art laboratory to test a range of polymer materials including polyethylene and polypropylene. ExcelPlas can carry out testing on plastic tube and pipe ranging in wall thickness from 3mm to 1200mm. ExcelPlas Laboratories provide a comprehensive service to Industrial & commercial companies, environmental consultants, Government bodies, and local Authority customers throughout Australia and Asia. All testing is carried and out in accordance with ASTM, ISO & WIS methods and is fully accredited to ISO 17025 by NATA.
- Butt Fusion Weld Testing
- Weld Testing
- Testing of Electro-fusion Welds
- Tear on saddle joints
- Crush De-cohesion of Electro-fusion welds
- Polymer & Plastics Identification
- Chemical & Thermal Testing
- Site Audits
ExcelPlas – the Australian Pipes & Fittings Testing Laboratory
- Accredited to ISO 17025 by the National Association of Testing Authorities (NATA) Australia, and is Australia’s largest laboratory dedicated for the testing of plastic pipes and fittings to various Standards which include Australian, European and International Standards.
- The staff employed at the laboratory have a combined experience of more than 85 years within the plastics industry specifically with manufacturing, quality control and the research and development of plastic piping systems including HDPE, PEX, PP-R, PVC, U-PVC, M-PVC, O-PVC, ABS, GRP, GRE and PB.
- Services provided include conformance testing, compliance testing, batch release testing, root cause analysis for field failures and non-destructive testing of samples.
ExcelPlas Lab Specialising in HDPE Pipe Condition Monitoring, Failure Analysis and Testing
In the event of a HDPE buttweld or electrofusion weld failing during initial testing, or in service, we can conduct investigations to assist in identifying the root cause of the failure.
This service also extends to the premature failure of the pipe or fitting itself.
http://www.excelplas.com/plastic-pipes
ExcelPlas Pipe Testing is a Leader in the Field of Polyethylene (PE) and High-Density Polyethylene (HDPE) Testing
ExcelPlas is accredited with the National Association of Testing Authorities (NATA) for butt weld tests, bend and tensile tests, peel decohesion tests on electro fusion sockets and failure mode determination
http://www.polypipetesting.com.au/butt-fusion-welds/
New UHMWPE Pipe for Tailing Offers Greater Than 4X the Abrasion Resistance of PE100 (Australia wide)
http://slurrypipes.com.au/
ExcelPlas Poly Pipe Weld Inspection Lists Top 7 Causes of Weld Failure:
- Lack of scraping
- Inaccurate scraping
- Contamination from dirt, water, oil or clays
- Lack of Paralell-ness of fusion faces
- Misalignment of surfaces
- Time, temperature and pressure deviations
- Not adhering to cool times
We have extensive experience in inspection of poly pipe welds for assuring welded joint quality. Direct Poly Pipe Inspection ensures that operators are following the proven welding procedure; this reduces the occurrences of operational errors which lead to defects such as inclusions, lack of fusion (LoF), porosity and misalignment.
More information, contact [email protected]
Get Your HDPE Pipe Products or Services Noticed – Advertise in Poly Pipe News (PPN) Australia
https://www.polypipenews.com.au/advertise/
This Newsletter is brought to you by Excelplas Labs, Australia’s Largest group of Poly Pipe Testing Labs.
Pipe Poly News (PPN) is now Australia’s most current and comprehensive source of news on Polyethylene pipes and Poly Pipe Welding;
Poly Pipe News is now sent to over 4500 Poly Pipe Industry Members every week.
Any news requests should be sent to [email protected]
To subscribe, visit https://www.polypipenews.com.au/subscribe/
2023 Copyright ExcelPlas Labs
PPN is owned and operated by ExcelPlas Pty Ltd. By subscribing to PPN you agree to receiving regular PPN newsletters as well as the PPN platform using your email contact details to enhance the performance and functionality of PPN and its analytics reports. These email contact details allow PPN to track page views and create more targeted and relevant content. PPN provides an unsubscribe link on the bottom of each PPN newsletter.
